I've decided to part out my race bike, so everything is going up for sale.

Atermarket parts
Suspension
Forks with Traxxion Dyamics internals and .95 springs (for riders weighing around 190 pounds in gear)

Protection
Lightning performance frame sliders

Controls
CRG Supersport clutch/clutch perch (please see pictures for condition)
Gilles Rearsets (see pictures for condition)

Brakes
Galfer Wave Rotors (fronts only)
Double banjo bolt w/ brake light switch (thread pitch for aftermarket Brembo master cylinder)

Cosmetics
Godfather racing black/green race bodywork (also includes two stock ram air tubes and PUIG DB windscreen).
Stock gas tank (painted green/black/silver. Has Stomp Grip pads installed)

Engine/Exhaust
Race baffled exhaust
16 tooth Ti-moly front sprocket (520 pitch)
46 tooth black rear sprocket (520 pitch)
43 tooth Vortex rear sprocket (520 pitch)

Stock parts
Motor
Frame
Subframe
Upper triple tree
Lower triple tree
Front brake calipers
Rear brake caliper
Stock rotors
Stock steering dampner


List will be updated regularly to reflect new parts, and to have sold parts removed.

Here is the CRG Supersport clutch and clutch perch:

http://img76.imageshack.us/img76/2851/clutch3ab1.th.jpg (http://img76.imageshack.us/my.php?image=clutch3ab1.jpg)

http://img300.imageshack.us/img300/1470/clutch2ry1.th.jpg (http://img300.imageshack.us/my.php?image=clutch2ry1.jpg)

http://img292.imageshack.us/img292/435/clutch1mt8.th.jpg (http://img292.imageshack.us/my.php?image=clutch1mt8.jpg)

The piece that connects the clutch lever to the clutch perch, and that actually pivots, would need to be replaced for this to function as new. Currently, that piece is causing the clutch lever to feel bent up, as you can see in the picture where I am holding the perch horizontal, but the lever is bent up.

Race bodywork (includes the three pieces pictured here, as well as two stock ram air ducts (black), PUIG windscreen, and the front fender (not painted)):

http://img72.imageshack.us/img72/1117/img4189xx5.th.jpg (http://img72.imageshack.us/my.php?image=img4189xx5.jpg)

Fork tube clamp and stock steering dampner (you need the fork tube clamp if you use aftermarket clipons):

http://img179.imageshack.us/img179/5696/img4185cv1.th.jpg (http://img179.imageshack.us/my.php?image=img4185cv1.jpg)

Gilles rearsets (this is their exact condition. I raced with them like this for 4 race weekends):

http://img72.imageshack.us/img72/5654/img4187co3.th.jpg (http://img72.imageshack.us/my.php?image=img4187co3.jpg)

http://img166.imageshack.us/img166/2429/img4179bd4.th.jpg (http://img166.imageshack.us/my.php?image=img4179bd4.jpg)

Panterra keyless gas cap:

http://img65.imageshack.us/img65/1231/panterragascapaq6.th.jpg (http://img65.imageshack.us/my.php?image=panterragascapaq6.jpg)

Galfer Wave rotors (fronts only):

http://img224.imageshack.us/img224/2545/frontwheel2ks0.th.jpg (http://img224.imageshack.us/my.php?image=frontwheel2ks0.jpg)

http://img143.imageshack.us/img143/7540/frontwheel1cf7.th.jpg (http://img143.imageshack.us/my.php?image=frontwheel1cf7.jpg)

Race baffled exhaust, left and right cannisters (I cannot tell you the number of times I have received compliments for how the bike sounds.):

http://img409.imageshack.us/img409/7922/rightexhaustnb4.th.jpg (http://img409.imageshack.us/my.php?image=rightexhaustnb4.jpg)

http://img409.imageshack.us/img409/8253/leftexhausthx2.th.jpg (http://img409.imageshack.us/my.php?image=leftexhausthx2.jpg)

Lightning Performance fame sliders and clutch slider. This was my unused, spare set.

http://img100.imageshack.us/img100/558/frameclutchslidersjc9.th.jpg (http://img100.imageshack.us/my.php?image=frameclutchslidersjc9.jpg)

46 tooth, 520 pitch rear sprocket:

http://img232.imageshack.us/img232/3875/46toothsprockettu2.th.jpg (http://img232.imageshack.us/my.php?image=46toothsprockettu2.jpg)

Woodcraft clip-ons (one bar is a little bent and could probably do with replacing. I just rotated the clip-ons so the bar bent away from me, and then adjusted the whole bar in closer):

http://img482.imageshack.us/img482/4828/cliponsiw7.th.jpg (http://img482.imageshack.us/my.php?image=cliponsiw7.jpg)

How much for the bodywork, gas cap & exhaust?

Post some prices homie!

I don't think he wants to sell us anything.

Inten_Z, you have a PM.

Tracker, let me know what you're interested in.

I have since picked up everything I need to race this year....as long as I stay off the pavement naps...

Good luck on the sale...Thought it would be best for you to post prices when you can so people will get more excited.

PM sent...

If intent doesn't already have dibs, gas cap, and sliders.

Are you selling the cans or the whole exhaust?

How Much For The Frame And Te Exhaust? Interested In Both Thanks

How much do you want for both triples shipped to 54110

interested in the frame sliders and crg levers. Any prices?